DNP Setting Not Respected

Hi Upverter,

I’ve got a design with several off-board parts, for which I checked the “DNP” button so that they only appear in my schematic and BOM and not in my layout. For one of the parts, J1 in my schematic, although the DNP button is checked, the part is still appearing in my layout. Am I doing something wrong? Is this a bug? Something else?

Design ID: bc1c20aaeda773da

Thanks,
Cheinan

Hi Cheinan,
thank you for reporting.
We will investigate this issue and get back to you.

I ended up removing the part as it was blocking my board layout, but I assume you can look into the history. Let me know if I can help you figure this out.

No verified component could be evaluated for this task.

Skipped:

* m.asif: Skip * Abubakr_Ramadan: later

Accepted:


Rejected:

Created by Christian1993

(compare candidates)

Discard reason: Multiple common required attribute values

Created by D.TATA

(compare candidates)

Discard reason: Multiple common required attribute values

Created by jorman

(compare candidates)

Discard reason: Multiple common required attribute values

This is an automated post.

No verified component could be evaluated for this task.

Skipped:

* m.asif: Skip * Abubakr_Ramadan: later

Accepted:


Rejected:

Created by Christian1993

(compare candidates)

Discard reason: Required attribute mismatch

Created by D.TATA

(compare candidates)

Discard reason: Multiple common device class attribute values

Created by jorman

(compare candidates)

Discard reason: Multiple common device class attribute values

Created by pickworth

(compare candidates)

Discard reason: Required attribute mismatch

This is an automated post.

@D.TATA @pickworth @Christian1993
Max Overall Height: 5.334 mm
Resolution: Blank(The output is analog)
Output Voltage: 500 mV
Mfg Package Ident Date: 0
Accuracy: Blank

it should be enter in 0.21 inch

updated

This task has been verified. Edits are no longer accepted.

Verified component:


Skipped:

* m.asif: Skip * Abubakr_Ramadan: later

Accepted:

Created by D.TATA

(compare with verified)

Created by jorman

(compare with verified)

Created by pickworth

(compare with verified)


Rejected:

Created by Christian1993

(compare with verified)



This is an automated post.

hey now i was checking. I was offline, please consider revert this rejection @haroldocalvo

@le.yu @haroldocalvo @eugene.kim.pcb
Please Can you revert this rejection? I enter to the system just 2 minutes before they verify the piece, was not on the PC and could not check from the phone, please reverse this rejection this time.

The Mfg Ident is incorrect. Not a minor thing.

Yes, i know but you posted this: https://forum.upverter.com/t/microchip-mcp9700-e-to/66163/9?u=christian1993 30 minutes ago when i was offline in addition to when I open the link, it takes me to the official microchip page and not to a drawing package. I was checking the link that you posted and where is the latest package drawing when the part was verified. It should be noted that i have to check two forums in the same time.

The functional link to get the latest package drawing is this: http://www.microchip.com/mymicrochip/filehandler.aspx?ddocname=en595808

not this:
https://ww1.microchip.com/downloads/en/DeviceDoc/3L_TO-92%20Plastic%20Transistor%20Outline_TO_C04-00101c.pdf

@haroldocalvo @eugene.kim.pcb This is Samson
What is the procedure to join in this community?
I’m willing to join in our community

Seems like you are already joined

@eugene.kim.pcb @haroldocalvo
I would like to join in parts-specialists, What is the procedure to join in parts-specialists?
add me to…